-40%
Makermotor 110vac 220vac 10RPM Gearmotor Variable Speed Brushless ECM Gear Motor

Makermotor 110vac 220vac 10RPM Gearmotor Variable Speed Brushless ECM Gear Motor

$ 100.32

Availability: 87 in stock
  • Refund will be given as: Money back or replacement (buyer's choice)
  • Modified Item: No
  • Custom Bundle: No
  • Restocking Fee: No
  • MPN: PN00211
  • Product Type: Motor Controls
  • Model: PN00211
  • All returns accepted: Returns Accepted
  • Condition: New
  • Return shipping will be paid by: Buyer
  • Item must be returned within: 30 Days
  • Brand: Makermotor

    Description

    10 RPM (Rotisserie) Gear Motor 115V 230V Reversible Variable Speed
    Due to its low speed property and its variable speed feature.  This motor is ideal for a low speed rotisserie application.
    For the rotisserie application, be sure to set up bearings specifically to hold up the weight of the meat so the motor is
    only to rotate the meat with minimum axial and radial loads.  Also, flexible couplings are highly recommended for a
    direct-drive set up.  Due to the nature of a BBQ rotisserie's high temperature environment, make sure the motor is
    placed far enough from the heat to prevent failures of the motor's mechanical or electrical components.  A fire wall
    should be considered to protect the motor.  This motor was tested with a 50kg (110lb) of weight with its variable speed
    feature at ease.  The 50kg (110lb) weight is to simulate a 50kg (110lb) hog/pig that is traditionally roasted with an
    outdoor BBQ rotisserie set up.
    This is a compact, single-phase, 115v ac to 230v ac input,  permanent magnet, BRUSHLESS gear motor with reversible,
    on/off, speed adjustable controls. Speed range varies depending on the shaft load.  Motor's maximum speed is 10 RPM.
    Rotation is reversible by a signal wire.
    This combination will be described in two parts: brushless dc gear motor and power adapter.
    Brushless 12VDC Gear Motor:  24 N-m (17.7 ft-lb) torque at 10 RPM.  Permanent magnet rotor.  60mm x 60mm square
    motor with 56mm diameter gear box.  4 M5 threaded holes located at front for face mounting. Motor length is 6.75 inch
    (171mm) long and its controller is integrated as part of the motor.  Shaft is 12mm in diameter with a flat and is 1 inch
    (25.4mm) long.  The control line, which contains speed adjustment (with a pot soldered already), reversing signal wire,
    on/off signal wire, and signal ground wire, is 14 inch (356mm)long.  Connector line that is to connect to the power
    adapter is 14 inch (356mm) long.  Motor control is very simple.  To turn the motor on, simply disconnect the on/off (blue)
    wire to signal ground (black) wire.  A typical practice is to introduce a switch between the on/off wire and the ground wire.
    To reverse the rotation of the motor, simply connect the reverse (white) wire to the same ground wire and the motor will
    reverse its rotation.  PLEASE BE SURE THAT THE MOTOR IS AT FULL STOP BEFORE REVERSING. To vary the
    speed, simply turn the potentiometer.
    Power Adapter:  The power cord is 5 ft(152 cm) long and has a standard plug ready to plug into a standard appliance
    outlet.  The adapter is able to universally accept 115v ac or 230v ac.  Connector line that is to connect to the motor is 3
    ft (91 cm) long.  Adapter's dimensions are 2.5 in(64mm) width by4.75in(121mm) length by 1.75in(44mm) depth.